我司是專業從事于金屬磷化加工的高科技企業。
現有全自動磷化加工線4條，在職員工190人，主要從事錳系磷化加工，鋅系磷化加工，黑色錳系磷化加工，涂裝磷化加工。
產品磷化膜外觀均勻一致，很黑。并且具有很高的防腐性能，鹽霧時間48-96小時.
公司已通過了ISO9001-2008(實驗室)，TS16949質量體系認證。
工藝設備配套
通過缸體表面積得到槽體的體積，合理規定鋼件表面積和磷化液體積比，防止磷化液一直工作產生大量的鐵離子，導致磷化液顏色變黑。磷化槽子一般單位體積的負載量是8平方米每噸，不能大于18平方米，不然，由于槽液負載太大，磷化液消耗太快，不固定，不好調整。
槽子的制作
主要有船狀的槽子和長方形槽子，前面的一直生產比較方便，后面的用于間隔式加工。槽子所用的材質要能承受磷化液的酸洗和溫度，要有足夠的剛度承擔磷化液的載重卻不變形，磷化液槽子要用不銹鋼的。特別是高溫錳系磷化液溫度比較高，所以一定要用不銹鋼的槽子。如果用PP槽子就必須達到12毫米厚度，也有槽子用鋼筋水泥做成，里面加一層塑料板或玻璃鋼防止腐蝕。這種槽子成本較小，方便與做大的槽體。
船型的槽子有一定的坡度，方便手機磷化渣，坡度一般在磷化槽子的底邊，把渣沉到底部。
也能在四周排布，把渣放到指定的位置。
攪拌措施
使用風機把磷化液不斷攪拌，使磷化膜生成均勻一致，除油的槽子一小時要攪拌6次，表調一小時3次，磷化液一小時10次。像一些大的槽子，底部槽子的流動情況很重要，它將影響到一直排渣的能不能順利進行下去。
Through the cylinder body surface area to get the volume of trough, reasonable regulation steel parts surface area and phosphatization liquid product ratio, prevent phosphating solution has been work produces a large number of iron ion, resulting in phosphating solution color black. Phosphating slot general unit volume capacity is 8 square meters per ton, is not greater than 18 square meters, otherwise, due to the tank liquid load is too big, phosphating liquid consumption too fast, not fixed, bad adjustment. Groove making Mainly has scaphoid trough and rectangular slot, front had been producing more convenient, behind for interval type processing. Trough the material to be able to withstand phosphating solution of pickling and temperature, want to have enough stiffness bear phosphating liquid load but not deformation, phosphating liquid trough to use stainless steel. Especially in high temperature manganese series phosphating solution temperature is higher, so be sure to use stainless steel slot. If with PP manger must reach 12 mm thickness, also have made trough with reinforced concrete, which add a layer of plastic board or glass reinforced plastics to prevent corrosion. The manger cost is small, convenient and do big tub. Form of groove has a certain slope, convenient mobile phone phosphate slag. |
 |
|
手機站
您當前位置是：商業機會 >> 化工 >> 化工助劑 >> 上海磷化加工︱上海酸洗磷化加工︱上海黑色磷化加工
聯系信息