| 耐沖壓金屬油墨系列 適用于各種金屬、玻璃、陶瓷、石材、電鍍(含水電鍍)、陽極氧化鋁表面、靜電噴漆面及烤漆面等制品的絲印及移印，不需加固化劑，不需烘烤，即可獲得優異的附著力。油墨特性：1、平光(如需亮光請選擇我司JL系列)、附著力佳、耐酒精、耐化學品；2、手感好，流平性佳、面光潔；3、表面硬度好，耐沖擊性能強、抗刮傷；4、耐酒精、耐化學品程度佳；印刷：選用網目為100-420目，以120T聚酯單絲、感光膠網版計算涂覆蓋面積每公斤達35~40㎡。表干時間自然揮發5-10分鐘，實干時間在24小時以內，48小時后達*佳性能。1.用B-03專用稀釋劑開油水2.用718洗網水洗網。3.可選擇添加JS-9硬化劑10%用于增加油墨附著力及物理化學抗性。4.烤箱80℃烘烤30分鐘佳能更優。測試方法(完全干燥后)：1.3M膠紙粘在畫有百格的油墨表面45度角迅速拉起不脫油。2.純度99%的酒精500G力在油墨表面來回擦拭200次無脫色。使用方法：1.使用前應充分攪拌，用后隨時密封。2.攪拌時先加固化劑靜置10分鐘后，再加稀釋劑10-15%，稀釋到印刷粘度。3. 加入固化劑的油墨使用時限為4-6小時，過期請棄用，剩余油墨不可回收。4.網版塞網時可用洗網水清洗。5.不得與其它類型油墨混合使用。注意事項：1.各種物料的外觀相似，但可能會是不同的材料，客戶需先試印，確其符合要求后，再批量生產。2.在移印過程中，如出現拉絲或散開現象，可適當加入一些慢干膏即可。3.環境溫度過高，將會影響油墨原有質量。4.請遠離火源，避光保存。 Resistance to stamping metal ink series in the application of metal, glass, ceramic, stone, electroplating (water cut electroplating), anodic alumina surface, electrostatic spray paint surface and paint surface and so on screen printing products and pad printing, not needing curing agent, and does not need to bake, can obtain excellent adhesion. Ink features: 1, PingGuang (such as light please choose to our JL series), adhesion, good resistance to alcohol, resistance to chemicals; 2, feel is good, flow ping sex, good surface is bright and clean; 3 and fine surface hardness, impact resistance performance is strong, resistance to scratch; 4, resistant to alcohol, resistant to chemicals degree good; Printing: choose the mesh is 100-420 yard, and with 120 T polyester monofilament, photosensitive plastic nets edition calculation area covered with per kilogram of 35 to 40 ㎡. Dry time table natural volatilize 5-10 minutes, action in time within 24 hours, after 48 hours of optimum performance. 1. To use B-03 special thinner, open oil-water 2. With 718 wash nets washing nets. 3. Can choose to add JS-9-10 � and � � stiffening agent to increase physical and chemical resistance and adhesion of ink. 4. Preheat the oven to 80 ℃ bake 30 minutes more optimal Canon. |
 |
|
手機站
您當前位置是：商業機會 >> 化工 >> 油墨 >> 供應耐高溫金屬油墨系列-上海耐酸堿金屬油墨系列-耐沖壓金屬油墨系列
聯系信息
