 |
膠水公司
| 聯系人：王小姐
女士 (主管) |
| 電 話：021-51693135 |
手 機：13052326431  |
 |
|
 |
|
| CATALYST 24LV電子組裝/工業膠水/電子組裝膠水/工業用膠 |
CATALYST 24LV電子組裝/工業膠水/電子組裝膠水/工業用膠
技術服務熱線：021-51693135 / 021-22818476
Catalyst 24LV encapsulate is recommended for applications where high compressive stress is applied to encapsulated circuitry - as in deep ocean work.
This product will have a minimum effect on electronic circuit operation and shows negligible deformation and water absorption.
Storage Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 18 to 25 °CDIRECTIONS FOR USE1.
Accurately weigh resin and hardener into a clean container in the recommended ratio.2. Mix thoroughly in the can in which it is received.3.
Liquid diluents can be supplied to lower viscosity at some sacrifice in properties.4. Pour mixture into cavity or mold.5. Mold release 122 S will prevent adhesion.
(Evacuation may be necessary to remove trapped air and is recommended for high quality embedment’s.
It is often convenient to remove the trapped air from the resin prior to pouring into mold, and then again evacuate briefly when the mold is filled).6. Allow to stand at room temperature for about 4 hours.
Removal from the mold prior to that time is possible if the casting is hard.7.
The filler will tend to float during storage. Premixing before use is required.
推薦使用催化劑24LV密封劑用于高壓縮應力應用于封裝電路的應用，如在深海工程中。
該產品對電子電路操作具有*小的影響，顯示出可忽略的變形和吸水性。
Storage Store產品在未開封的容器中干燥處。存儲信息可能在產品容器標簽上顯示。*佳存儲：18至25°使用光盤1。
以推薦的比例精確稱重樹脂和固化劑成為清潔容器。
在收到的罐中徹底混合。可以提供液體稀釋劑以降低粘度，同時犧牲一些特性。將混合物倒入腔或模具中。脫模122將防止粘附。
（疏散可能需要去除被困的空氣，建議用于高質量的嵌入，通常在澆注模具之前將樹脂中的空氣從樹脂中去除，然后在模具填充時再次抽出）。
允許在室溫下靜置約4小時。如果鑄件很難，可以在此之前從模具中取出。
在儲存期間，填料將傾向于浮動。使用前需要預混。 |
 |
| |
|
|
 |
|
|
免責聲明：以上所展示的信息由會員自行提供，內容的真實性、準確性和合法性由發布會員負責，www.qy6.com對此不承擔任何責任。如有侵犯您的權益，請來信通知刪除。