HYSOL GR2220電子膠水/塑封膠水/漢高樂泰膠水/塑封方案HYSOL GR2220電子膠水/塑封膠水/漢高樂泰膠水/塑封方案HYSOL GR2220電子膠水/塑封膠水/漢高樂泰膠水/塑封方案HYSOL GR2220電子膠水/塑封膠水/漢高樂泰膠水/塑封方案HYSOL GR2220電子膠水/塑封膠水/漢高樂泰膠水/塑封方案HYSOL GR2220電子膠水/塑封膠水
HYSOL GR2220電子膠水/塑封膠水/漢高樂泰膠水/塑封方案
技術服務熱線：021-51693135 / 021-22818476
樂泰 HYSOL GR 2220 epoxy molding compound deliversoutstanding performance and ease of use.TYPICAL PROPERTIES OF UNCURED MATERIALSpiral Flow, @ 175°C, inches 32Gel Time @ 175 °C, seconds 18Shelf Life @ 5°C (from date of manufacture), days 365 pecific Gravity, g/cm3 1.82TYPICAL PROCESS DATAHandlingMolding Temperature, °C 160 to 200Transfer Pressure, Kgf/cm2 40 to 80Transfer Time, seconds 5 to 15Curing Time, @ 180 °C, seconds 70 to 100Post Mold Cure @ 175 °C, hours 4 to 12Hot Hardness @ 175 °C 87樂泰 HYSOL GR 2220 has been formulated to provide the bestpossible moldability and as wide a molding latitude as possible.
Although molding and curing conditions will vary from situation tosituation, recommended starting ranges are shown above.
TYPICAL PROPERTIES OF CURED MATERIALAll measurements are taken at 175oC, unless otherwise noted.All physical, electrical and analytical measurements are taken onspecimens cured for 120 seconds @ 175°C with post cure of 6hours@ 175°C, unless otherwise specified.
Physical PropertiesGlass Transition Temperature, °C 161Coefficient of Thermal Expansion :
Below Tg, ppm/°C 18.5Above Tg, ppm/°C 63.3Conversions(°C x 1.8) + 32 = °FkV/mm x 25.4 = V/milmm / 25.4 = inchesN x 0.225 = lbN/mm x 5.71 = lb/inN/mm2 x 145 = psi
MPa = N/mm2MPa x 145 = psiN•m x 8.851 = lb•inN•m x 0.738 = lb•ftN•mm x 0.142 = oz•in
mPa•s = cP
樂泰 HYSOL GR 2220環氧樹脂模塑復合材料具有出色的性能和易用性。
175℃，英寸32Gel時間175℃下的固化材料螺旋流動的特性特性：秒5秒（從制造日期起）比重，g /cm31.82特殊工藝數據處理模具溫度，°C 160至200轉印壓力Kgf /cm240至80轉印時間秒5至15℃固化時間，@ 180°C，秒70至100后模具固化175℃，小時4至12硬度@ 175°C 87樂泰 HYSOL |
 |
|
手機站
您當前位置是：產品大全 >> 化工 >>
膠粘劑
免責聲明：以上所展示的信息由會員自行提供，內容的真實性、準確性和合法性由發布會員負責，www.qy6.com對此不承擔任何責任。如有侵犯您的權益，請來信通知刪除。
10
聯系信息
