樂泰 363平板電腦/筆記本ipad專用膠水，樂泰膠水
技術服務熱線：021-51693135 / 021-22818476
樂泰® 363™ is designed for shallow potting and thin-film encapsulating of electronic assemblies. TYPICAL PROPERTIES OF UNCURED MATERIAL Specific Gravity @ 25 °C 1.1 Flash Point - See MSDS Viscosity, Brookfield - RVT, 25 °C, mPa•s (cP): Spindle 1, speed 20 rpm 100 to 400LMS TYPICAL CURING PERFORMANCE This product is cured when exposed to UV radiation of 365nm. To obtain a full cure on surfaces exposed to air, radiation at 250nm is also required. The speed of cure will depend on the UV intensity as measured at the product surface. Typical cure condition is 20-30 seconds at 100mW/cm2 using a medium pressure, quartz envelope, mercury vapor lamp. Tack Free Time Tack Free Time is the time required to achieve a tack free surface Tack Free Time, seconds: 100 mW/cm2, measured @ 365 nm 25 Fixture Time Fixture time is defined as the time to develop a shear strength of 0.1 N/mm2. UV Fixture Time, Glass microscope slides, seconds: 6 mW/cm2, measured @ 365 nm ≤15LMS 100 mW/cm2, measured @ 365 nm 5
樂泰®363™設計用于電子組件的淺灌封和薄膜封裝。固化材料的典型特性25°C時的比重1.1閃點 - 參見MSDS粘度，Brookfield - RVT，25°C，mPa•s（cP）：主軸1，轉速20 rpm 100至400LMS典型固化性能本產品固化當暴露于365nm的紫外線輻射。為了在暴露于空氣的表面上獲得完全固化，也需要在250nm的輻射。固化速度將取決于在產品表面測量的紫外線強度。典型的固化條件為：在100mW / cm 2的情況下，使用中壓，石英外殼，汞蒸氣燈，為20-30秒。無空閑時間粘貼時間是實現無粘性表面所需的時間無空閑時間秒秒：100毫瓦/厘米2，在365nm測量25夾具時間夾具時間定義為開發剪切強度為0.1N / mm2。 UV固定時間，玻璃顯微鏡載玻片，秒：6mW / cm 2，在365nm±15nm±100mW / cm 2下測量，在365nm |
 |
|
手機站
您當前位置是：產品大全 >> 化工 >>
膠粘劑
免責聲明：以上所展示的信息由會員自行提供，內容的真實性、準確性和合法性由發布會員負責，www.qy6.com對此不承擔任何責任。如有侵犯您的權益，請來信通知?jiǎng)h除。
10
聯系信息
